Schneider LXM32AD18M2 Motion servo drive - Lexium 32 - single phase supply voltage 115/230V - 0.5/1kW
| range of product |
Lexium 32
|
|
|---|---|---|
| product or component type |
Motion servo drive
|
|
| device short name |
LXM32A
|
|
| format of the drive |
Book
|
|
| network number of phases |
Single phase
|
|
| [Us] rated supply voltage |
100...120 V (- 15...10 %)
200...240 V (- 15...10 %) |
|
| supply voltage limits |
170...264 V
85...132 V |
|
| supply frequency |
50/60 Hz (- 5...5 %)
|
|
| network frequency |
47.5...63 Hz
|
|
| EMC filter |
Integrated
|
|
| continuous output current |
6 A (f = 8 kHz)
|
|
| output current 3s peak |
10 A at 115 V for 5 s
18 A at 230 V for 5 s |
|
| maximum continuous power |
500 W at 115 V
1600 W at 230 V |
|
| nominal power |
0.5 kW at 115 V (f = 8 kHz)
1 kW at 230 V (f = 8 kHz) |
|
| line current |
8.5 A, THDI of 147 % at 115 V, without line choke
8.4 A, THDI of 148 % at 230 V, without line choke 9.9 A, THDI of 74 % at 115 V, with external line choke of 2 mH 10.6 A, THDI of 93 % at 230 V, with external line choke of 2 mH |
| switching frequency |
8 kHz
|
|
|---|---|---|
| overvoltage category |
III
|
|
| leakage current |
<= 30 mA
|
|
| output voltage |
<= power supply voltage
|
|
| electrical isolation |
Between power and control
|
|
| type of cable |
Single-strand IEC cable (for θ = 50 °C) conductor material:
copper 90 °C ,wire insulation material: XLPE/EPR
|
|
| electrical connection |
Terminal cable 3 mm² AWG 12 (CN8)
Terminal cable 5 mm² AWG 10 (CN1) Terminal cable 5 mm² AWG 10 (CN10) |
|
| tightening torque |
0.5 N.m (CN8)
0.7 N.m (CN1) 0.7 N.m (CN10) |
|
| discrete input number |
1 capture
2 safety 4 logic |
|
| discrete input type |
Capture (CAP)
Logic (DI) Safety (compliment of STO_A, compliment of STO_B) |
|
| sampling duration |
0.25 ms (DI) for discrete
|
|
| discrete input voltage |
24 V DC for capture
24 V DC for logic 24 V DC for safety |
|
| discrete input logic |
Positive (compliment of STO_A, compliment of STO_B) at State 0:
< 5 V at State 1: > 15 V conforming to EN/IEC 61131-2 type 1
Positive (DI) at State 0: > 19 V at State 1: < 9 V conforming to EN/IEC 61131-2 type 1 Positive or negative (DI) at State 0: < 5 V at State 1: > 15 V conforming to EN/IEC 61131-2 type 1 |
|
| response time |
<= 5 ms (compliment of STO_A, compliment of STO_B)
|
|
| discrete output number |
2
|
|
| discrete output type |
Logic (DO) 24 V DC
|
|
| discrete output voltage |
<= 30 V DC
|
|
| discrete output logic |
Positive or negative (DO) conforming to EN/IEC 61131-2
|
|
| contact bounce time |
<= 1 ms (compliment of STO_A, compliment of STO_B)
2 µs (CAP) 0.25 µs...1.5 ms (DI) |
|
| braking current |
50 mA
|
|
| response time on output |
250 µs (DO) discrete
|
|
| control signal type |
Servo motor encoder feedback
|
|
| protection type |
Against reverse polarity :inputs signal
Against short-circuits :outputs signal |
|
| safety function |
STO (safe torque off), integrated
|
|
| safety level |
SIL 3 conforming to EN/IEC 61508
PL = e conforming to ISO 13849-1 |
|
| communication interface |
Integrated CANopen
Integrated Modbus Integrated CANmotion |
|
| connector type |
RJ45 (labelled CN4 or CN5) :CANmotion
RJ45 (labelled CN4 or CN5) :CANopen RJ45 (labelled CN7) :Modbus |
|
| method of access |
Slave
|
|
| commissioning port |
2-wire RS485 multidrop Modbus
|
|
| transmission rate |
1 Mbps for bus length of 4 m CANopen, CANmotion
125 kbps for bus length of 500 m CANopen, CANmotion 250 kbps for bus length of 250 m CANopen, CANmotion 50 kbps for bus length of 1000 m CANopen, CANmotion 500 kbps for bus length of 100 m CANopen, CANmotion 9600, 19200, 38400 bps for bus length of 40 m Modbus |
|
| number of addresses |
CANopen, CANmotion
Modbus |
|
| communication service |
1 receive SDO CANmotion
1 transmit SDO CANmotion 2 PDOs conforming to DSP 402 CANmotion 2 SDOs receive CANopen 2 SDOs send CANopen 4 configurable mapping PDOs CANopen CANopen device profile drives and motion control CANopen, CANmotion Display of faults on integrated display terminal Modbus Emergency CANopen, CANmotion Event-triggered, time-triggered, remotely requested,sync (cyclic), sync(acyclic) CANopen Node guarding, heartbeat CANopen Position control mode CANmotion Position control, speed profile, torque profile and homing mode CANopen Sync CANmotion |
|
| status LED |
1 LED (red) servo drive voltage
1 LED error 1 LED RUN |
|
| signalling function |
Display of faults in 7 segments
|
|
| marking |
CE
|
|
| operating position |
Vertical +/- 10 degree
|
|
| product compatibility |
Servo motor BMH (70 mm, 1 motor stacks)
Servo motor BMH (70 mm, 2 motor stacks) Servo motor BMH (70 mm, 3 motor stacks) Servo motor BMH (100 mm, 1 motor stacks) Servo motor BSH (55 mm, 3 motor stacks) Servo motor BSH (70 mm, 1 motor stacks) Servo motor BSH (70 mm, 2 motor stacks) Servo motor BSH (70 mm, 3 motor stacks) Servo motor BSH (100 mm, 1 motor stacks) |
|
| width |
48 mm
|
|
| height |
270 mm
|
|
| depth |
237 mm
|
|
| product weight |
1.8 kg
|
| electromagnetic compatibility |
Conducted EMC at class A group 1 conforming to EN 55011
Conducted EMC at class A group 2 conforming to EN 55011 Conducted EMC at environment 2 category C3 conforming to EN/IEC 61800-3 Conducted EMC at category C2 conforming to EN/IEC 61800-3 Conducted EMC at environments 1 and 2 conforming to EN/IEC 61800-3 Electrostatic discharge immunity test at level 3 conforming to EN/IEC 61000-4-2 Susceptibility to electromagnetic fields at level 3 conforming to EN/IEC 61000-4-3 1.2/50 µs shock waves immunity test at level 3 conforming to EN/IEC 61000-4-5 Electrical fast transient/burst immunity test at level 4 conforming to EN/IEC 61000-4-4 Radiated EMC at class A group 2 conforming to EN 55011 Radiated EMC at category C3 conforming to EN/IEC 61800-3 |
|
|---|---|---|
| standards |
EN/IEC 61800-3
EN/IEC 61800-5-1 |
|
| product certifications |
CSA
RoHS TÜV UL |
|
| IP degree of protection |
IP20 conforming to EN/IEC 60529
IP20 conforming to EN/IEC 61800-5-1 |
|
| vibration resistance |
1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC
60068-2-6
1 gn (f = 13...150 Hz) conforming to EN/IEC 60068-2-6 |
|
| shock resistance |
15 gn for 11 ms conforming to EN/IEC 60028-2-27
|
|
| pollution degree |
2 conforming to EN/IEC 61800-5-1
|
|
| environmental characteristic |
Classes 3C1 conforming to IEC 60721-3-3
|
|
| relative humidity |
Class 3K3 (5 to 85 %) without condensation conforming to IEC
60721-3-3
|
|
| ambient air temperature for operation |
0...50 °C conforming to UL
|
|
| ambient air temperature for storage |
-25...70 °C
|
|
| type of cooling |
Integrated fan
|
|
| operating altitude |
<= 1000 m without derating
> 1000...3000 m with conditions |
Schneider LXM32AD18M2 Motion servo drive
- Brand: Schneider
- Product Code: LXM32AD18M2
- Availability: 10
-
$1,000.00
- Ex Tax: $1,000.00
Tags: LXM32AD18M2